Craters

Made from the most brittle resin known to the Imperium, behold the crater set. Well okay not the full set, one of the small ones is missing but I have two of the larger ones.

The catalogue entry read “Huge craters are often torn in to the battlefield by artillery , bombs and other heavy weapons, and can provide a convenient form of cover should a squad find themselves under fire in otherwise open terrain.”

Humour seems to be dead in 40k these days but the smoking boots in one of the small craters always was a good conversation point.

Dating back to at least 2002 with a master model by Simon Harris and a set that sold for £18 when new.

Forgeworld product codes: FWK004/MO then TR-40K-S-002

Barricade

This is one of the three pieces that make up the Warhammer 40,000 Barricades Set 2. A complete set is made up of three piece resin barricades with each section approximately 6″ / 150mm long. Based on the photos I have seen I have the two curved sections (of which this is one), but not the straight middle bit.

The catalogue entry read “There are times when Imperial forces must make do with the materials at hand to construct barricades to help fortify areas to defend, and repel the enemy.”

Master model by Simon Harris around about 2002. The full set sold for £14.

Forgeworld product codes: FWF025 then TR-40K-S-022.

Fuel Dump

Another really nice bit of Forgeworld scenery, the classic fuel dump.

From factory in Nottingham this model saw too much resin in the mould and hadn’t had enough time on the belt sander after and so there was a good 4-5mm edge below the sculpt.

I added a piece of plasticard underneath to increase the base size by about 20mm all around and then built it up and blended the edge with various grades of sand before paint. Added insome additional bits of plasticard, skulls and imperial bits for effect too.

Master model by Simon Harris around 2002.

This was £12 when released.

Forgeworld Product Codes: FWF016 then TR-40K-S-017

The listing read “fuel dumps store the fuel required for each Imperial vehicle operating in the area. This one piece resin model makes a great objective for your games of Warhammer 40,000”.

Imperial Water / Fuel Tank

Not even Forgeworld could work out what this model was so it was listed as both a water tank and a fuel tank when it was available for sale.

This model was a bit bashed up when I received it so there are some photos in my Instagram feed of the repairs to it. Thin bits of resin snap easy so a bit of patience with plasticard to fix those. It turns out that bicycle spokes were perfect for the replacement of the runner bars at the top of the tank.

Master model by Simon Harris around 2005.

This was £20 when it was first released which for a big bit of resin seems really cheap and good value.

Forgeworld Product Code TR-40K-S-056

Pretty pleased with how that came out in the end. More use of the excellent waterslide transfers from the Mighty Brush featured here along with some Mechanicus decals from an Imperial Knights sheet too.

Small Barricade

Some time just little things can be good fun to paint up.

I am pretty sure that this piece is from the City Fight Barricades Set. This was a two part set.

I may well have the other part from the set in the box of bits but it has only been as I’ve written the post I’ve worked that out from the Forgeworld catalogue. I will need to have a rummage!

So I’m going to roll with that for now. The original blurb in the catalogue says:

There are times when Imperial forces must make do with the materials at hand to construct barricades to help fortify areas to defend, and repel the enemy. Two barricades made from oil drums and creates.

The two part master model by Simon Harris was originally £9 back in 2006

(Product Code TR-40K-S-008)

Forgeworld Ruined Chimera

The abandoned Chimera is a classic Forgeworld model that was originally available for pre-order way back in 2004.

Mine is a slight variation on the original model because the tank top doesn’t feature the sandbagged top hatch of the original casting. I am not sure it takes much away from it.

The excellent waterslide transfers from the Mighty Brush feature on my take on the Imperial Guard livery and tank markings.

This was a purchase off eBay and whilst I am confident it’s a legitimate original casting, it was a bit bashed up and so there were a few repairs to it before painting, notably the hooks on the shed and spare tank tracks that were snapped off and were repaired with styrene.

I am relatively new to using weathering powders but have been really impressed with them so far.

Original Forgeworld casting was by Simon Harris.

(Product code TR-40K-S-058) was £28 when it came out in 2004. They’re going for a fair bit more than that now!

A really nice model which I enjoyed painting and which I feel makes a good addition to my Forgeworld scenery collection.

Tank Traps and Pill Boxes

Forgeworld tank traps. These are used to block the movement of enemy ground based vehicles, slowing down any armoured assault. The kit contained three sets of Tank Traps based of a Master Model by Mark Bedford

(Product Code TR-40K-S-085..) was £18 for the set back in 2006,

Shown here with a ruined pillbox from Unreal Wargaming Studio.

Forgeworld Cities of Death Scenery

Painted up some more of the Forgeworld scenery from the stash.

Imperial underground building entrance as used on the desert world of Taros and other planets in the Imperium. Complete resin kit.

Model designed by Daren Parrwood for Forgeworld

(Product Code TR-40K-S-064) was only £16 when available around 2006

Ammo dumps are used by the Imperial Guard as a storage for the various types of ammunition the infantry and armour require.

This is a fantastic one piece resin model makes a great objective for your games of Warhammer 40,000.

Master model by Simon Harris for Forgeworld.

(Product Codes FWF017 then  TR-40K-S-018) was only £12 when available from around 2002.

Forgeworld City Fight Ruined Buildings

I loved going into Wargames and then as it became, Dice and Decks in Southport. Martin had a great setup and I really loved the Forgeworld scenery he had available for use.

When Martin decided just before the world went mad with COVID-19 to close the store and move to a warehouse and online setup he sold up a lot of furniture. I went in for a battle mat and a table and cheekily asked about the scenery.

No battle mats to be had, but a deal was done for the Forgeworld scenery and a long desire to get hands on with this amazing and now out of production scenery was done. So pleased to have managed to get this stuff.

As you’ll see form the photos it is not mint condition it’s all be used and is a bit worn, but it’s good enough for immediate use and with a few repairs will be back to a great standard in time!

Photographed here with some of my own stuff and a new Battlemat which I think works quite well in combination.

It’s definitely given me the appetite to try and get a few other bits and paint this stuff up!

Look at those barricades, there is a set of those of I remember rightly!