Barricade

This is another one of the three pieces that make up the Warhammer 40,000 Barricades Set 2. I posted the other curved section back in March. A complete set is made up of three piece resin barricades with each section approximately 6″ / 150mm long. I’ve still not tracked down the straight middle bit.

The catalogue entry read “There are times when Imperial forces must make do with the materials at hand to construct barricades to help fortify areas to defend, and repel the enemy.”

Master model by Simon Harris around about 2002. The full set sold for £14.

Forgeworld product codes: FWF025 then TR-40K-S-022.

Craters

Made from the most brittle resin known to the Imperium, behold the crater set. Well okay not the full set, one of the small ones is missing but I have two of the larger ones.

The catalogue entry read “Huge craters are often torn in to the battlefield by artillery , bombs and other heavy weapons, and can provide a convenient form of cover should a squad find themselves under fire in otherwise open terrain.”

Humour seems to be dead in 40k these days but the smoking boots in one of the small craters always was a good conversation point.

Dating back to at least 2002 with a master model by Simon Harris and a set that sold for £18 when new.

Forgeworld product codes: FWK004/MO then TR-40K-S-002

Barricade

This is one of the three pieces that make up the Warhammer 40,000 Barricades Set 2. A complete set is made up of three piece resin barricades with each section approximately 6″ / 150mm long. Based on the photos I have seen I have the two curved sections (of which this is one), but not the straight middle bit.

The catalogue entry read “There are times when Imperial forces must make do with the materials at hand to construct barricades to help fortify areas to defend, and repel the enemy.”

Master model by Simon Harris around about 2002. The full set sold for £14.

Forgeworld product codes: FWF025 then TR-40K-S-022.

Fuel Dump

Another really nice bit of Forgeworld scenery, the classic fuel dump.

From factory in Nottingham this model saw too much resin in the mould and hadn’t had enough time on the belt sander after and so there was a good 4-5mm edge below the sculpt.

I added a piece of plasticard underneath to increase the base size by about 20mm all around and then built it up and blended the edge with various grades of sand before paint. Added insome additional bits of plasticard, skulls and imperial bits for effect too.

Master model by Simon Harris around 2002.

This was £12 when released.

Forgeworld Product Codes: FWF016 then TR-40K-S-017

The listing read “fuel dumps store the fuel required for each Imperial vehicle operating in the area. This one piece resin model makes a great objective for your games of Warhammer 40,000”.

Imperial Water / Fuel Tank

Not even Forgeworld could work out what this model was so it was listed as both a water tank and a fuel tank when it was available for sale.

This model was a bit bashed up when I received it so there are some photos in my Instagram feed of the repairs to it. Thin bits of resin snap easy so a bit of patience with plasticard to fix those. It turns out that bicycle spokes were perfect for the replacement of the runner bars at the top of the tank.

Master model by Simon Harris around 2005.

This was £20 when it was first released which for a big bit of resin seems really cheap and good value.

Forgeworld Product Code TR-40K-S-056

Pretty pleased with how that came out in the end. More use of the excellent waterslide transfers from the Mighty Brush featured here along with some Mechanicus decals from an Imperial Knights sheet too.

Small Barricade

Some time just little things can be good fun to paint up.

I am pretty sure that this piece is from the City Fight Barricades Set. This was a two part set.

I may well have the other part from the set in the box of bits but it has only been as I’ve written the post I’ve worked that out from the Forgeworld catalogue. I will need to have a rummage!

So I’m going to roll with that for now. The original blurb in the catalogue says:

There are times when Imperial forces must make do with the materials at hand to construct barricades to help fortify areas to defend, and repel the enemy. Two barricades made from oil drums and creates.

The two part master model by Simon Harris was originally £9 back in 2006

(Product Code TR-40K-S-008)

Forgeworld Ruined Chimera

The abandoned Chimera is a classic Forgeworld model that was originally available for pre-order way back in 2004.

Mine is a slight variation on the original model because the tank top doesn’t feature the sandbagged top hatch of the original casting. I am not sure it takes much away from it.

The excellent waterslide transfers from the Mighty Brush feature on my take on the Imperial Guard livery and tank markings.

This was a purchase off eBay and whilst I am confident it’s a legitimate original casting, it was a bit bashed up and so there were a few repairs to it before painting, notably the hooks on the shed and spare tank tracks that were snapped off and were repaired with styrene.

I am relatively new to using weathering powders but have been really impressed with them so far.

Original Forgeworld casting was by Simon Harris.

(Product code TR-40K-S-058) was £28 when it came out in 2004. They’re going for a fair bit more than that now!

A really nice model which I enjoyed painting and which I feel makes a good addition to my Forgeworld scenery collection.

Command Edition Scenery

Wanted to get my hands on the new 9th Edition rules and having missed out on the limited edition boxed set (I made zero effort to get it, but was amused by the Games Workshop induced carnage), I thought the Command Edition starter set was spectacular value.

About the only downside of the scenery is that the building sections are not modular so a bit like the Ryza ruins they are what they are unless you want to take a razor saw to them and spend hours converting them.

The detail is what we have come to expect from the latest Games Workshop scenery and is fantastic makes painting them good fun.

Did experiment with some rust and charcoal weathering powders on these which I am quite happy with the results, particularly the rusted floor plates.

Some new variants on the thermo plasma or whatever they are conduit pipe sections. Simple paint job on these with Rust-oleum Gunmetal spray, detail work in greys and metallics, rust washes, gloss varnish and then oil washes. Sealed with satin finish.

Tank Traps and Pill Boxes

Forgeworld tank traps. These are used to block the movement of enemy ground based vehicles, slowing down any armoured assault. The kit contained three sets of Tank Traps based of a Master Model by Mark Bedford

(Product Code TR-40K-S-085..) was £18 for the set back in 2006,

Shown here with a ruined pillbox from Unreal Wargaming Studio.